|
Item |
Factory default setting |
Description |
||
|---|---|---|---|---|
|
Time Zone |
+00:00 |
Sets the time GMT zone. Available range: -12:00 to +13:00 (15 minutes / increment) |
||
|
Daylight Saving |
ON |
Sets whether to enable the Daylight Saving mode. |
||
|
Time Setup |
Auto Setup |
SNTP Server (Primary) |
|
Sets the SNTP server to use for setting the current date and time. You can enter up to 64 characters. |
|
SNTP Server (Secondary) |
||||
|
Manual Setup |
2001/01/01 0:00 |
Sets the current date and time manually. |
||
|
Power Setup |
Auto Power Off |
Auto Config |
Sets the behavior of Automatic Power Off. |
|
|
Power Supply Return |
State Continue |
Sets a power supply method at the time of recovery from the power failure. Select [Manual] if you do not want to make the machine automatically to turn on after the recovery. |
||
|
Office Document Mode (Except MC363) |
Mode1 |
This mode allows to always enable the toner save function. To forcibly enter the machine in toner save mode, select Mode2. |
||
|
High Humid Mode |
OFF |
Sets whether to enable the humidity mode. Selecting [Enable] reduces curl generated while printing. (MC363: On/Off only) |
||
|
Quiet Mode (Except MC363) |
OFF |
Sets whether to reduce the printing noise. Setting to [ON] affects printing speed. |
||
|
Drum Near Life Timing |
1000 |
Sets the timing for the near life warning for the drum cartridges. |
||
|
Fuser Near Life Timing |
1000 |
Sets the timing for the near life warning for the fuser unit. |
||
|
Belt Near Life Timing |
1000 |
Sets the timing for the near life warning for the belt unit. |
||
|
MF (Tone) / DP (Pulse) |
Tone |
Select a dial type. Tone Pulse |
||
|
Reception Mode |
Fax Ready Mode |
Sets a reception mode. Fax Ready Mode Tel / Fax Ready Mode Ans / Fax Ready Mode Tel Ready Mode DRD (Distinctive Ring Detection) |
||
|
DRD Type |
Type 1 |
Set Distinctive Ring Detection. Type 1 Type 2 Type 3 Type 4 |
||
|
Dial Tone Detection*2 |
OFF |
Sets whether to detect a dial tone. |
||
|
Busy Tone Detection |
ON |
Sets whether to detect a busy tone. |
||
|
Monitor Control |
OFF |
Select from three choices. OFF: Not to monitor. Type 1: To monitor for about five seconds after being connected to the sender when receiving faxes or from the time you are connected to the receiver to the time the fax signal is received when sending faxes. Type 2: To monitor all the time. |
||
|
Monitor Volume |
Middle |
Sets the Monitor Volume. OFF Low Middle High |
||
|
TTI Register / Edit |
TTI 1 |
(NULL) |
Registers or changes the transmission terminal identification (the name of a sender). You can enter up to 22 characters. |
|
|
TTI 2 |
||||
|
TTI 3 |
||||
|
Standard TTI |
TTI 1 |
Selects the default sender's name from the registered list. TTI 1 TTI 2 TTI 3 |
||
|
TTI Number |
(NULL) |
Register the fax number of this machine. |
||
|
TTI Calendar Type |
dd/mm/yyyy or mm/dd/yyyy |
Sets the calendar date format of sender's information. |
||
|
Super G3 |
ON |
Sets whether to use Super G3 (ultra high-speed communication mode). |
||
|
Wireless Module |
Disable |
Sets whether to enable or disable wireless LAN. |
||
|
Erase Privacy Data*1 |
- |
Deletes the registered privacy data.
|
||
|
Business Phone Setup |
Business Phone Cooperation |
Disable |
Sets whether to enable Business Phone Cooperation. |
|
|
Connection IP Address |
0.0.0.0 |
Sets the IP address of the connected device. |
||
|
Connection Port No. |
59000 |
Sets a port number of the connected device. |
||
-
A message is displayed to confirm the equipment restarts. Select [Yes] to continue. Select [No] to cancel.
-
When you set the dial tone detection setting to [ON], the machine does not dial if the dial tone is not detected.