Manage Unit

Operation Timeout

3

Sets time for automatic reset of screen to begin.

Available range: 1 to 10 minutes

Clear After Job

OFF

Sets whether to reset after job is completed.

Paper Jam Error Buzzer Volume

Middle

Sets the volume for the paper jam alert tone.

AirPrint Buzzer Volume

Low

Sets the AirPrint confirmation operation sound.

USB Menu

USB

Enable

Sets whether to enable USB.

Soft Reset

Disable

Sets whether to enable the soft reset command.

Speed

480Mpbs

Selects the maximum transfer speed of USB interface.

Offline Receive

Disable

Set whether to receive data in offline state or in recoverable error state.

Serial Number

Enable

Sets whether to use a USB serial number.

Connected Host

Normal

Sets a host to be connected.

Access Control

Disable

Sets access control.

Default Authentication Method Setting

Local Name

Available only when [Access Control] is set to [Enable].

Unit of Measure

Millimeter or Inch

Selects a displayed unit (millimeter / inch).

Default Paper Size

A4 or Letter

Sets the default paper size.

Date Format

dd/mm/yyyy or mm/dd/yyyy

Sets the date format.

Allow All Reports To Print

Disable

Sets whether to allow printing reports with personal information.

Near Life LED

Enable

Sets whether to light an LED if a near life warning occurs.

Near Life Status

Enable

Sets whether to display a message if a near life warning occurs.

Status Display

Toner Gauge

Specify display information in idle Display.

Paper Size: Display paper size of each tray.

Toner Gauge: Display toner gauge.

Panel Contrast

0

Sets the contrast of the display screen.

USB Memory Interface

Enable

If [Disable] is set, the print from USB Memory function cannot be used.

Power Save Time

1 minute

Sets when to enter Power Save mode.

Sleep Time

15 minutes

Sets when to enter Sleep mode.

Auto Power Off Time

4 hours

Sets when to enter Auto Power Off.

Silent Mode

ON

Specifies a print preparation operation when entering standby status from Sleep mode.

If [ON] is set: it is quiet as there is no print preparation.

If [OFF] is set: there is a rotation noise of the image to perform print preparation but you can start first printing early.

ECO Mode*¹

ON

If [ON] is set: Printing starts even before the temperature of the fuser reaches the prescribed degrees, if the job is small.

If [OFF] is set: Printing starts after the temperature of the fuser reaches the prescribed degrees.

Receive Buffer Size

Auto

Sets the reception buffer size that local interface secures.

Resource Save

OFF

Sets the resource save area.

Initialize

Execute

Initializes a flash memory.

This item is displayed when [Initial Lock] is set to [Disable].

Format Partition

PCL

(NULL)

Formats a partition.

Common

(NULL)

PS

(NULL)

Check File System

Execute

Resolves any mismatch between actual memory and displayed memory available in a file system and performs administration data (FAT information) recovery.

Initial Lock

Enable

Sets whether to give permission to change settings associated with the memory initialization.

Select Language

English

Selects display language for the display screen.

Initialize*¹

Execute

Deletes downloaded message files.

Cancel Key Behavior

Short

Sets the behavior when the (CANCEL) button is pressed.

Short: Pressing the button for less than 2 seconds cancels the job.

Long: Pressing the button for 2 to 5 seconds cancels the job.

Off: Pressing the (CANCEL) button does not cancel the job.

Inquiry Display

On

Sets whether to display the confirmation screen when cancelling the job.

Yes

Sets an option between "Yes" and "No" to be highlighted on the confirmation screen displayed when cancelling the job.

180

Sets timeouts for the confirmation screen of cancelling the job. When the confirmation screen timed out, printing is executed even the (CANCEL) button is pressed.

New Password

Verify password

999999

Changes the administrator password.

-

Deletes job macros and returns the settings to the default.

Save Settings

-

Saves the current settings.

The most recently performed settings are saved and the previous ones are overwritten.

Restore Settings

-

Replaces the settings with the saved ones.

This item is displayed only when "Save Settings" is performed and the settings are saved.

Clear Job Log*³

-

Clears the saved job logs.

Maintenance Counter

Disable

Sets whether to print the consumable counter's report.

Reset Main Counter

-

Resets the main counter.

Reset Supplies Counter

-

Reset the consumable counter.

This item is displayed when [Maintenance Counter] is set to [Enable].