Print Setup

Print Setup

Item

Factory default setting

Description

Copies

1

Sets the number of copies. For local printing, this setting is invalid except for demo data.

Available range: 1 to 999

Duplex

OFF or ON(Duplex)

Turns the duplex printing function on or off.

[OFF]: simplex printing

[Long Edge Bind]: duplex printing for long-edge binding

[Short Edge Bind]: duplex printing for short-edge binding

Media Check

Enable

Sets whether to check an inconsistency between the page size and the paper size in the tray.

Override A4 / Letter

Yes

Automatically switches paper to print from A4 to Letter if A4 document is to be printed with A4 paper run out and Letter paper loaded, from Letter to A4 if Letter document is to be printed with Letter paper run out and A4 paper loaded.

Resolution

600dpi

Sets the resolution.

Toner Save

Toner Save Level

OFF

Sets the amount of toner to be saved.

This setting is enabled when copying, printing, printing received faxes, and printing from USB Memory.

Mono-Print Mode

Auto

Sets the print mode for black-and-white pages.

Orientation

Portrait

Sets the page orientation.

Edit Size

Cassette size

Sets the size of the printable page area if the size is not specified with the paper edit size command from a computer.

Trapping

OFF

Set trapping

Width / Length

210 mm (8.3 inch) or 216 mm (8.5 inch)

Sets the width of a custom paper size.

Available range: 64 to 216 mm (2.5 to 8.5 inches)

297 mm (11.7 inch) or 279 mm (11 inch)

Sets the length of a custom paper size.

Available range: 90 to 1,321 mm (3.5 to 52.0 inches)

Printer Adjust

Item

Factory default setting

Description

Manual Timeout

60 seconds

Sets for how many seconds the machine waits for paper to be fed before cancelling a job when using the manual feeder.

Timeout Injob

40 seconds

Sets a time interval from when the machine stops receiving data to when it starts a forced printing.

Timeout Local

40 seconds

Sets how long each port is left opened after a job is complete. (The network is excluded.)

Timeout Network

90 seconds

Sets how long the network port is left opened after a job is complete.

Print Mode Without Color Toner

Alarm

Sets whether to print the document in black and white or stop with alarm when a color toner empty error occurs.

Jam Recovery

Enable

Sets whether to print the pages again that are not printed due to a paper jam after the jam is cleared.

Paper Black Setting

0

Adjusts finely if the black contrast becomes weak or blots or lines become conspicuous when printing on plain paper.

If fine blots or lines appear, decrease the value. If the dark part becomes light, increase the value.

Paper Color Setting

0

Adjusts finely if the color contrast becomes weak, or blots or lines become conspicuous when printing on plain paper.

If fine blots or lines appear, decrease the value. If the dark part becomes light, increase the value.

SMR Setting

Black

0

Corrects variations in print results caused by temperature and humidity conditions and differences in print density and frequency. Change the setting if the print quality is uneven.

Yellow

0

Magenta

0

Cyan

0

BG Setting

Black

0

Corrects variations in print results caused by temperature and humidity conditions and differences in print density and frequency. Change the setting if the background is dark.

Yellow

0

Magenta

0

Cyan

0

HU Setting

OFF

Sets the mode to remove stain generated while being left for a long time.

VL Cleaning

-

Cleans the image drum.

Set this mode when vertical white lines appear on the output.

Gloss Mode

OFF

Raises the fusing temperature and prints highly glossy images.

Set to [ON] when printing highly glossy images.

Print Position Adjust

Item

Factory default setting

Description

Tray 1

X Adjust

0 mm

  • X Adjust: Adjusts the position of the entire printing image perpendicular to the direction of paper movement.

    Available range: ±2.00 mm (0.25 mm increments).

  • Y Adjust: Adjusts the position of the entire printing image parallel to the direction of paper movement.

    Available range: ±2.00 mm (0.25 mm increments).

  • Duplex X Adjust: Adjusts the position of the image on the back side of a duplex print perpendicular to the direction of paper movement.

    Available range: ±2.00 mm (0.25 mm increments).

  • Duplex Y Adjust: Adjusts the position of the image on the back side of a duplex print parallel to the direction of paper movement.

    Available range: ±2.00 mm (0.25 mm increments).

Y Adjust

0 mm

Duplex X Adjust

0 mm

Duplex Y Adjust

0 mm

Tray 2/3 (Optional)

X Adjust

0 mm

Y Adjust

0 mm

Duplex X Adjust

0 mm

Duplex Y Adjust

0 mm

MP Tray

X Adjust

0 mm

Y Adjust

0 mm

Duplex X Adjust

0 mm

Duplex Y Adjust

0 mm

Drum Cleaning

Item

Factory default setting

Description

Drum Cleaning

OFF

Sets whether to clean the drum before printing. The image quality improvement may be expected.

Hex Dump

Item

Factory default setting

Description

Hex Dump

OFF

Prints out the data received from the host computer in hex. To finish printing, turn the machine off.

Item

Factory default setting

Description

Density Control

Auto

Select "Auto" or "Manual" for adjusting density.

Adjust Density

-

Adjusting density is performed right after this menu is selected.

Color Tuning / Print Pattern

-

A test page is printed for checking the adjusting value to be entered for any other C/M/Y/K Tuning menus.

Cyan Tuning

Cyan Highlight

0

Adjust the value for Highlight / Mid-tone / Dark of each color within a range of -3 to +3.

+ : Adjusted to be darker.

- : Adjusted to be lighter.

Cyan Mid-Tone

0

Cyan Dark

0

Magenta Tuning

Magenta Highlight

0

Magenta Mid-Tone

0

Magenta Dark

0

Yellow Tuning

Yellow Highlight

0

Yellow Mid-Tone

0

Yellow Dark

0

Black Tuning

Black Highlight

0

Black Mid-Tone

0

Black Dark

0

Color Density

Cyan Density

0

Adjust the total density of each color within a range of -3 to +3.

+ : Adjusted to be darker.

- : Adjusted to be lighter.

Magenta Density

0

Yellow Density

0

Black Density

0

Adjust Registration

Color registration adjustment is performed.

Ink Simulation

OFF

Sets the ink simulation. This setting is enabled only for PS language jobs.

UCR

Low

Adjusts the level of under color removal.

CMY100% Density

Disable

Selects whether to use halftone for C, M, Y 100% density.

CMYK Conversion

ON

Selects whether to use simple (quick) mode when performing CMYK Conversion.

This menu setting is disabled if using the ink simulation function.

Item

Factory default setting

Description

Personality

Auto Emulation

Selects the emulation mode. If auto is set, the correct emulation is automatically selected every time a print job is received.

Alarm Release

Manual

If [Manual] is set, non-critical warnings, such as requests for a different paper size, can be cleared by pressing [RESET]. If [Auto] is set, the warnings are cleared when the print job resumes.

Auto Continue

OFF

Sets whether the machine automatically recovers from a memory overflow.

Error Report

OFF

Sets whether to print error details if PostScript, PCL6, or XPS errors occur.

Item

Factory default setting

Description

Font Source

Resident

Selects the location of the font to use.

Font No.

I0

Selects the font number to use.

Available range: I0 to I90 if [Resident] is set/C1 to C4 if [Resident 2] is set.

Font Pitch

10.00 CPI

Sets the width of the PCL default font.

Available range: 0.44 to 99.99 CPI. (0.01CPI increments)

It is displayed when the font that is selected by [Font No.] is the outline font of fixed spacing.

Font Height

12.00 points

Sets the height of the PCL default font.

Available range: 4.00 to 999.75 point. (0.25 point increments)

It is displayed when the font that is selected by [Font No.] is the outline font of proportional spacing.

Symbol Set

PC-8

Selects a PCL symbol set.

A4 Print Width

78 Column

Sets the number of digits for automatic line feed on A4 paper.

White Page Skip

OFF

Selects whether to print blank pages.

CR Function

CR

Sets the machine operation when receiving CR code.

LF Function

LF

Sets the machine operation when receiving LF code.

Print Margin

Normal

Sets the nonprintable area of the page.

True Black

OFF

Selects whether to print black image data using mixed CMYK or print using black toner only.

Pen Width Adjust

ON

Sets whether to emphasize thin lines so that the lines look thicker.

Tray ID#

Tray 1

1

Sets a value that specifies a tray with the PCL paper source specification command.

Available range: 1 to 59

Tray 2 (Optional)

5

Tray 3 (Optional, Except MC363)

20

MP Tray

4

Item

Factory default setting

Description

L1 Tray

Type 1

Set the paper tray number for the Level 1 operator.

[Type 1]: The effective number for paper tray starts from 1.

[Type 2]: The effective number for paper tray starts from 0.

Network PS-Protocol

RAW

Specifies PS communication protocol mode of data from Network.

USB PS-Protocol

RAW

Specifies PS communication protocol mode of data from USB.

PDF Paper Size

Current Tray Size

Set the paper size when printing with PDF Direct Print.

PDF Scaling Size

99%

Sets reduction rate for PDF when [PDF Paper Size] is set to [Scaling Size].

PDF Print Mode

High Quality

Sets the priority order between the print quality and print speed when printing PDF.

Item

Factory default setting

Description

DigitalSignature

OFF

Sets the DigitalSignature functions.

DiscardControl

Auto

Sets the DiscardControl function.

MC Mode

ON

Sets the MarkupComaptibility function.

Unzip Mode

Speed

Sets the XPS file decompression method.

White Page Skip

OFF

Selects whether to output blank pages in XPS.

Item

Factory default setting

Description

SIDM Manual ID#

2

Set up Pn specified in MANUAL by MANUAL-1 ID No.FX/PPR Emu in CSF control command (ESC EM Pn).

SIDM Manual2 ID#

3

Set up Pn specified in MANUAL by MANUAL-2 ID No.FX/PPR Emu in CSF control command (ESC EM Pn).

SIDM MP Tray ID#

4

Set up Pn specified TRAY 0 (MP Tray) by MP Tray ID No.FX/PPR Emu in CSF control command (ESC EM Pn).

SIDM Tray1 ID#

1

Set up Pn specified TRAY 1 by Tray 1 ID No.FX/PPR Emu in CSF control command (ESC EM Pn).

SIDM Tray2 ID#

(Optional)

5

Set up Pm specified TRAY 2 by Tray 2 ID No.FX/PPR Emu in CSF control command (ESC EM Pn).

SIDM Tray3 ID#

(Optional, Except MC363)

6

Set up Pn specified TRAY 3 by Tray 3 ID No.FX/PPR Emu in CSF control command (ESC EM Pn).

Item

Factory default setting

Description

Character Pitch

10 CPI

Specifies character pitches in IBM PPR emulation.

Font Condense

12CPI to 20CPI

Specifies 12CPI pitches for Condense Mode.

Character Set

SET-2

Specifies a character set.

Symbol Set

IBM-437

Specifies a symbol set.

Letter O Style

Disable

Specifies the style that replaces 9BH with letter o and 9DH with a zero.

Zero Character

Normal

Sets the zero to be slashed or unslashed.

Line Pitch

6 LPI

Specifies the line spacing.

White Page Skip

OFF

Selects whether to print blank pages.

CR Function

CR

Selects a carriage return from [CR] or [CR+LF].

LF Function

LF

Selects a line feed from [LF] or [LF+CR].

Line Length

80 Column

Specifies the number of characters per line.

Form Length

11.7 inch or 11 inch

Specifies the length of paper.

TOF Position

0.0 inch

Specifies the distance from the top edge of paper.

Left Margin

0.0 inch

Specifies the distance from the left edge of paper so that the print starting point shifts to the right horizontally.

Fit to Letter

Disable or Enable

Sets the printing mode that can fit paper to the printable area equivalent to 11 inches (66 lines).

Text Height

Same

Sets the height of a character.

SAME: The height stays the same regardless of CPI.

DIFF: The height varies according to CPI.

Item

Factory default setting

Description

Character Pitch

10 CPI

Specifies character pitches.

Character Set

SET-2

Specifies a character set.

Symbol Set

IBM-437

Specifies a symbol set.

Letter O Style

Disable

Specifies the style that replaces 9BH with letter o and 9DH with a zero.

Zero Character

Normal

Sets the zero to be slashed or unslashed.

Line Pitch

6 LPI

Specifies the line spacing.

White Page Skip

OFF

Selects whether to print blank pages.

CR Function

CR

Select a carriage return from [CR] or [CR+LF].

Line Length

80 Column

Specifies the number of characters per line.

Form Length

11.7 inch or 11 inch

Specifies the length of paper.

TOF Position

0.0 inch

Specifies the distance from the top edge of paper.

Left Margin

0.0 inch

Specifies the distance from the left edge of paper so that the print starting point shifts to the right horizontally.

Fit to Letter

Disable or Enable

Sets the printing mode that can fit paper to the printable area equivalent to 11 inches (66 lines).

Text Height

Same

Sets the height of a character.

SAME: The height stays the same regardless of CPI.

DIFF: The height varies according to CPI.

Item

Factory default setting

Description

Verify job option

Disable

Set whether to verify a job before printing.

If enabled, the machine verifies that the job is not altered before starting printing. The security is enhanced, however it will take longer to start printing.

Erase job option

No overwrite

Set how to delete a job.

You can overwrite deleted data so that it will not be restored.

If enabled, it will take longer to delete.

Available value: No overwrite/Zero out once

Keep job for

2 hours

Set the storage period of jobs.

If the set period elapses after jobs are stored, the jobs will be automatically deleted.

Available value:

15 minutes/30 minutes/1 hour/2 hours/4 hours/8 hours/12 hours/1 day/2 days/3 days/4 days/5 days/6 days/7 days

Job Limitation

Disable

Sets whether to save a restricted print job.

If [Private Print Only] is selected, print jobs other than private print are not accepted.

Job Password Authentication

OFF

Sets whether to verify a job password when the access control is enabled.