Manage Unit

Item			Factory default setting	Description
Default Mode			Home	Sets the default mode screen of this machine.
Operation Clear	Operation Timeout		3	Sets time for automatic reset of screen to begin. Available range: 1 to 10 minutes
Operation Clear	Clear After Job		OFF	Sets whether to reset after job is completed.
Sound Control	Key Touch Tone Volume		Middle	Sets the volume of the key-touch tone.
	Copy Buzzer Volume		Middle	Sets the volume for the copy complete sound.
	FAX Buzzer Volume		Middle	Sets the volume for the transmission complete sound.
	JAM Buzzer Volume		Middle	Sets the volume for the paper jam alert tone.
	AirPrint Buzzer Volume		Low	Sets the AirPrint confirmation operation sound.
Local Interface*¹	USB Menu	USB	Enable	Sets whether to enable USB.
		Soft Reset	Disable	Sets whether to enable the soft reset command.
		Speed	480Mpbs	Selects the maximum transfer speed of USB interface.
		Offline Receive	Disable	Set whether to receive data in offline state or in recoverable error state.
		Serial Number	Enable	Sets whether to use a USB serial number.
		USB Assignment	IPP	Selects IPP-USB or Legacy for USB assignment. When scanning via USB, select Legacy.
System Setup	Access Control		Disable	Sets access control.
	User Authentication Method		Local	Display condition: [Access Control] is set to [User] or [Password].
	Unit of Measure		Millimeter or Inch	Selects a displayed unit (millimeter / inch).
	Default Paper Size		A4 or Letter	Sets the default paper size.
	Date Format		dd/mm/yyyy or mm/dd/yyyy	Sets the date format.
	Allow All Reports To Print		Disable	Sets whether to allow printing reports with personal information.
	Near Life LED		Enable	Sets whether to light an LED if a near life warning occurs.
	Status in Near Life		Enable	Sets whether to display a message if a near life warning occurs.
	Address Information Lock Time Out		30 minute(s)	Sets time until a lock is released by the machine when an address book, telephone book, or profile is kept locked by the utilities. Available range: 1 to 60 minutes
	USB Memory Interface		Enable	If [Disable] is set, the Scan To USB Memory and the print from USB Memory functions cannot be used.
	Panel Brightness During Operating		7	Sets the LCD panel brightness. Available range: 1 to 7 (1 increments)
	Panel Brightness While Power Save		0	Sets the LCD panel brightness. Available range: 0 to 7 (1 increments)
	Panel Calibration		Execute	Executes LCD panel calibration.
	Output Tray Paper Exist Lamp		Enable	Selects whether to flash LED when paper remains on the Upper Output Tray. Only for the models mounted the Upper Output Tray.
Power Save	Power Save Time		1 minute	Sets when to enter Power Save mode.
	Sleep Time		15 minutes	Sets when to enter Sleep mode.
	Auto Power Off Time		4 hours	Sets when to enter Auto Power Off.
	Silent Mode		ON	Specifies a print preparation operation when entering standby status from Sleep mode. If [ON] is set: it is quiet as there is no print preparation. If [OFF] is set: there is a rotation noise of the image to perform print preparation but you can start first printing early.
	ECO Mode*¹		ON	If [ON] is set: Printing starts even before the temperature of the fuser reaches the prescribed degrees, if the job is small. If [OFF] is set: Printing starts after the temperature of the fuser reaches the prescribed degrees.
Memory Setup	Receive Buffer Size		Auto	Sets the reception buffer size that local interface secures.
Memory Setup	Resource Save		OFF	Sets the resource save area.
Flash Memory Setup*¹	Initialize		Execute	Initializes a flash memory. Display condition: [Initial Lock] is set to [Disable].
HDD Setup*¹	Initialize		Execute	Initializes a hard disk. Display condition: [Initial Lock] is set to [Disable].
	Format Partition	PCL	(NULL)	Formats a partition.
		Common	(NULL)
		PS	(NULL)
Storage Maintenance Setup	Check File System		Execute	Resolves any mismatch between actual memory and displayed memory available in a file system and performs administration data (FAT information) recovery.
	Check All Sectors		Execute	Performs recovery of a defective HDD sector information and a file system mismatch as mentioned above.
	Erase HDD		Execute	This function erases all data on the hard disk.
	Initial Lock		Enable	Sets whether to give permission to change settings associated with the memory initialization.
Encryption Setup	Job Limitation		Disable	If [Encrypted Job only] is selected, all requests for print except encrypted authentication printing are ignored. If [ID Secure Job only] is selected, all printing jobs except for ID secured jobs are ignored.
Language Maint Setup	Select Language		English	Selects display language for the LCD panel.
Language Maint Setup	Initialize*¹		Execute	Deletes downloaded message files.
Admin Password	New Password Enter password (Verify)		aaaaaa	Changes the administrator password. 6 to 12 characters can be used.
Reset Settings*²			Execute	Deletes job macros, fax transmission / reception data, and the history information, and returns the settings to the default.
Job Log Setup	Clear Job Log*³		Execute	Clears the saved job logs.
Print Statistics	Supplies Report		Disable	Sets whether to print the consumable counter's report.
	Reset Main Counter		Execute	Resets the main counter.
	Reset Supplies Counter		Execute	Reset the consumable counter. Display condition: [Supplies Report] is set to [Active].

A message is displayed to confirm the equipment restarts automatically when changes have been made. Select [Yes] to continue. Select [No] to cancel.
A message is displayed to confirm the equipment restarts automatically when executed. Select [Yes] to continue. Select [No] to cancel.
A message is displayed to confirm that all job logs are deleted when executed. Select [Yes] to continue. Select [No] to cancel.