User Install

Time Zone

00:00

Sets the time GMT zone.

Available range: -12:00 to +13:00 (15 minutes / increment)

Daylight Saving

ON

Sets whether to enable the Daylight Saving mode.

Time Setup

Auto Setup

SNTP Server (Primary)

Sets the SNTP server to use for setting the current date and time. You can enter up to 64 characters.

SNTP Server (Secondary)

Manual Setup

2001/1/1 0:00

Sets the current date and time manually.

Power Setup

Auto Power Off

Auto Config

Sets the behavior of Automatic Power Off.

High Humid Mode

OFF

Sets whether to enable the curl reduction mode.

◆OFF (Factory default setting):

Set to OFF if the toner came off when printed paper was rubbed and/or uneven gloss occurred when printing on the plain paper setting. However, paper curl may increase.

<Precautions when changing the setting>

Setting [Mode1 to 4] shortens the lifetime of the image drum due to the process change. Depending on your usage environment, [Mode0] and OFF are also the same.

◆Mode0:

<Usage effects>

It reduces paper curl.

<Precautions for use>

Set to OFF if the toner came off when printed paper was rubbed and/or uneven gloss occurred when printing on the plain paper setting. However, paper curl may increase.

◆Mode1/Mode2:

<Usage effects>

Set to Mode1/Mode2 if you want to reduce paper curl though the toner came off when printed paper was rubbed and/or uneven gloss occurred when printing on the plain paper setting. If [Mode1] does not reduce paper curl, change to [Mode2]. [Effect: Mode1 < Mode2]

<Precautions for use>

The warm-up time is longer than when selecting Mode0/OFF, and the print speed slows down. (The warm-up time in [Mode2] is longer than that in [Mode1].) Effects of paper curl reduction is lower than Mode0.

◆Mode3/Mode4:

<Usage effects>

Set to Mode3/Mode4 to prevent paper jams at the image drum when duplex printing is performed on thin paper. [Effect: Mode3 < Mode4]

<Precautions for use>

The warm-up time is longer than when selecting Mode0/OFF, and the print speed slightly slows down. [Mode3] and [Mode4] are effective only on the [Plain paper] setting. Set to [Mode3], then change to [Mode4] if the desired effect is not achieved.

◆Mode5:

Selecting Mode5 performs the same as selecting [OFF].

Drum Near Life Timing

3000

Sets the timing for the near life warning for the drum cartridges.

Fuser Near Life Timing

2500

Sets the timing for the near life warning for the fuser unit.

Belt Near Life Timing

2000

Sets the timing for the near life warning for the belt unit.

MF (Tone) / DP (Pulse)

Tone

Select a dial type.

Tone

Pulse

Reception Mode

Fax Ready Mode

Sets a reception mode.

Fax Ready Mode

Tel / Fax Ready Mode

Ans / Fax Ready Mode

Tel Ready Mode

DRD (Distinctive Ring Detection)

DRD Type

Type 1

Set Distinctive Ring Detection.

Type 1

Type 2

Type 3

Type 4

Dial Tone Detection*²

OFF

Sets whether to detect a dial tone.

Busy Tone Detection

ON

Sets whether to detect a busy tone.

Monitor Control

OFF

Select from three choices.

OFF: Not to monitor.

Type 1: To monitor for about five seconds after being connected to the sender when receiving faxes or from the time you are connected to the receiver to the time the fax signal is received when sending faxes.

Type 2: To monitor all the time.

Monitor Volume

Middle

Sets the Monitor Volume.

OFF

Low

Middle

High

TTI Register / Edit

TTI 1

(NULL)

Registers or changes the transmission terminal identification (the name of a sender). You can enter up to 22 characters.

TTI 2

TTI 3

Standard TTI

TTI 1

Selects the default sender's name from the registered list.

TTI 1

TTI 2

TTI 3

TTI Number

(NULL)

Register the fax number of this machine.

TTI Calendar Type

dd/mm/yyyy or mm/dd/yyyy

Sets the calendar date format of sender's information.

Super G3

ON

Sets whether to use Super G3 (ultra high-speed communication mode).

Wireless Module

Disable

Erase Privacy Data*¹

Execute

The following data are deleted.

• E-mail address list, phone book, data registered in profiles, one touch buttons, etc.

• Administrator password, values set in the menu

• Fax transmission/reception data

• Authentication printing/encrypted authentication printing data

• Various histories

Display condition: Print Job Accounting and smart PrintSuperVision are disabled.